Methyl cyanoacetate
Product identifier
- Product name: Methyl cyanoacetate
- CBnumber: CB9485583
- CAS: 105-34-0
- EINECS Number: 203-288-8
- Synonyms: methyl 2-cyanoacetate,Methyl cyanoacetate
Relevant identified uses of the substance or mixture and uses advised against
- Relevant identified uses: For R&D use only. Not for medicinal, household or other use.
- Uses advised against: none
Company Identification
- Company: Chemicalbook
- Address: Building 1, Huihuang International, Shangdi 10th Street, Haidian District, Beijing
- Telephone: 400-158-6606
GHS Label elements, including precautionary statements
-
Symbol(GHS)
- Signal wordWarning
Substance
- Product name: Methyl cyanoacetate
- Synonyms: methyl 2-cyanoacetate,Methyl cyanoacetate
- CAS: 105-34-0
- EC number: 203-288-8
- MF: C4H5NO2
- MW: 99.09
Description of first aid measures
General adviceMost important symptoms and effects, both acute and delayed
Indication of any immediate medical attention and special treatment needed
Extinguishing media
Suitable extinguishing mediaSpecial hazards arising from the substance or mixture
Carbon oxides Nitrogen oxides (NOx) Combustible.
Vapors are heavier than air and may spread along floors. Forms explosive mixtures with air on intense heating.
Development of hazardous combustion gases or vapours possible in the event of fire.
Advice for firefighters
In the event of fire, wear self-contained breathing apparatus.
Further information
Suppress (knock down) gases/vapors/mists with a water spray jet. Prevent fire extinguishing water from contaminating surface water or the ground water system.
NFPA 704
| HEALTH | 2 | Intense or continued but not chronic exposure could cause temporary incapacitation or possible residual injury (e.g. diethyl ether, ammonium phosphate, iodine) | |
| FIRE | 1 | Materials that require considerable preheating, under all ambient temperature conditions, before ignition and combustion can occur. Includes some finely divided suspended solids that do not require heating before ignition can occur. Flash point at or above 93.3 °C (200 °F). (e.g. mineral oil, ammonia) | |
| REACT | 0 | Normally stable, even under fire exposure conditions, and is not reactive with water (e.g. helium,N2) | |
| SPEC. HAZ. |
Personal precautions, protective equipment and emergency procedures
Advice for non-emergency personnel: Do not breathe vapors, aerosols. Avoid substance contact. Ensure adequate ventilation. Evacuate the danger area, observe emergency procedures, consult an expert.
For personal protection see section 8.
Environmental precautions
Do not let product enter drains.
Methods and materials for containment and cleaning up
Cover drains. Collect, bind, and pump off spills. Observe possible material restrictions (see sections 7 and 10). Take up with liquid-absorbent material (e.g. Chemizorb? ). Dispose of properly. Clean up affected area.
Reference to other sections
For disposal see section 13.
Precautions for safe handling
For precautions see section 2.2.
Conditions for safe storage, including any incompatibilities
Storage conditions
Tightly closed.
Storage class
Storage class (TRGS 510): 10: Combustible liquids
Specific end use(s)
Apart from the uses mentioned in section 1.2 no other specific uses are stipulated
control parameter
Hazard composition and occupational exposure limitsExposure controls
Personal protective equipmentUse equipment for eye protection tested and approved under appropriate
government standards such as NIOSH (US) or EN 166(EU). Safety glasses
This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN374 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).
Full contact
Material: butyl-rubber
Minimum layer thickness: 0,7 mm
Break through time: 480 min Material tested:Butoject? (KCL 898)
This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN374 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).
Splash contact Material: Chloroprene
Minimum layer thickness: 0,65 mm Break through time: 240 min Material tested:KCL 720 Camapren?
protective clothing
required when vapours/aerosols are generated.
Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system.
Recommended Filter type: Filter type ABEK
The entrepeneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer.
These measures have to be properly documented.
Do not let product enter drains.
Information on basic physicochemical properties
- Appearancecolorless liquid
- Odouraromatic
- Odour ThresholdNo data available
- pHNo data available
- Melting point/freezing pointMelting point/range: 13 °C
- Initial boiling point and boiling range204 - 207 °C
- Flash point110 °C - closed cup - Regulation (EC) No. 440/2008, Annex, A.9
- Evaporation rateNo data available
- Flammability (solid, gas)No data available
- Upper/lower flammability or explosive limitsNo data available
- Vapour pressure 0,13 hPa at 20 °C
- Vapour density 3.41 (vs air)
- Relative density1,123 g/mL at 25 °C 1,12 at 20 °C
- Water solubility54 g/l at 20 °C - completely soluble
- Partition coefficient: n-octanol/waterNo data available
- Autoignition temperature 478 °C at 1.013 hPa
- Decomposition temperatureNo data available
- ViscosityViscosity, kinematic: No data available Viscosity, dynamic: 3 mPa.s at 20 °C
- Explosive propertiesNo data available
- Oxidizing propertiesNo data available
Other safety information
No data available
Reactivity
Forms explosive mixtures with air on intense heating.
A range from approx. 15 Kelvin below the flash point is to be rated as critical.
Chemical stability
The product is chemically stable under standard ambient conditions (room temperature) .
Possibility of hazardous reactions
Violent reactions possible with:
Strong oxidizing agents Strong acids
strong alkalis
strong reducing agents
Conditions to avoid
Strong heating.
Incompatible materials
No data available
Hazardous decomposition products
In the event of fire: see section 5
Information on toxicological effects
Acute toxicity(OECD Test Guideline 401) Inhalation
LD50 Dermal - Rat - male and female - > 2.000 mg/kg (OECD Test Guideline 402)
Result: No skin irritation - 4 h (OECD Test Guideline 404)
Result: Eye irritation - 24 h (OECD Test Guideline 405)
Test system: Salmonella typhimurium
Metabolic activation: with and without metabolic activation Method: OECD Test Guideline 471
Result: negative
Toxicity
Persistence and degradability
Biodegradability aerobic - Exposure time 28 d
Result: 99 % - Readily biodegradable. (OECD Test Guideline 301A)
Bioaccumulative potential
No data available
Mobility in soil
No data available
Results of PBT and vPvB assessment
This substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher.
Other adverse effects
No data available
Avoid release to the environment.
Waste treatment methods
Product
See www.retrologistik.com for processes regarding the return of chemicals and containers, or contact us there if you have further questions.
UN number
ADR/RID: - IMDG: - IATA: -
UN proper shipping name
Transport hazard class(es)
ADR/RID: - IMDG: - IATA: -
Packaging group
ADR/RID: - IMDG: - IATA: -
Environmental hazards
ADR/RID: no IMDG Marine pollutant: no IATA: no
Special precautions for user
Further information
Not classified as dangerous in the meaning of transport regulations.
Safety, health and environmental regulations/legislation specific for the substance or mixture
Regulations on the Safety Management of Hazardous ChemicalsAbbreviations and acronyms
- CAS: Chemical Abstracts Service
- ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
- RID: Regulation concerning the International Carriage of Dangerous Goods by Rail
- IMDG: International Maritime Dangerous Goods
- IATA: International Air Transportation Association
- TWA: Time Weighted Average
- STEL: Short term exposure limit
- LC50: Lethal Concentration 50%
- LD50: Lethal Dose 50%
- EC50: Effective Concentration 50%
References
【1】CAMEO Chemicals, website: http://cameochemicals.noaa.gov/search/simple
【2】ChemIDplus, website: http://chem.sis.nlm.nih.gov/chemidplus/chemidlite.jsp
【3】ECHA - European Chemicals Agency, website: https://echa.europa.eu/
【4】eChemPortal - The Global Portal to Information on Chemical Substances by OECD, website: http://www.echemportal.org/echemportal/index?pageID=0&request_locale=en
【5】ERG - Emergency Response Guidebook by U.S. Department of Transportation, website: http://www.phmsa.dot.gov/hazmat/library/erg
【6】Germany GESTIS-database on hazard substance, website: http://www.dguv.de/ifa/gestis/gestis-stoffdatenbank/index-2.jsp
【7】HSDB - Hazardous Substances Data Bank, website: https://toxnet.nlm.nih.gov/newtoxnet/hsdb.htm
【8】IARC - International Agency for Research on Cancer, website: http://www.iarc.fr/
【9】IPCS - The International Chemical Safety Cards (ICSC), website: http://www.ilo.org/dyn/icsc/showcard.home
【10】Sigma-Aldrich, website: https://www.sigmaaldrich.com/
The information in this MSDS is only applicable to the specified product, unless otherwise specified, it is not applicable to the mixture of this product and other substances. This MSDS only provides information on the safety of the product for those who have received the appropriate professional training for the user of the product. Users of this MSDS must make independent judgments on the applicability of this SDS. The authors of this MSDS will not be held responsible for any harm caused by the use of this MSDS.